cyrilus31 wrote:Ce n'est pas la bonne image Jibel
je viens de la corriger et c'est good
cyrilus31 wrote:Ce n'est pas la bonne image Jibel
Code: Select all
sudo smartctl -a /dev/sda
cyrilus31 wrote:Et donc en mettant boot comme drapeau sur la partition sda1, ton installation de MX15 depuis le disque dur ne veut pas se lancer, c'est exact?
Essaie la commande suivante stp pour vérifier l'état de ton disque durCode: Select all
sudo smartctl -a /dev/sda
Code: Select all
jib@mx1jib:~
$ sudo smartctl -a /dev/sda
[sudo] password for jib:
smartctl 6.4 2014-10-07 r4002 [i686-linux-3.16.0-4-686-pae] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint M
Device Model: SAMSUNG MP0804H
Serial Number: S042J20A121444
Firmware Version: UE100-14
User Capacity: 80.026.361.856 bytes [80,0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 0
Local Time is: Mon Jun 19 10:29:08 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4800) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 80) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 3136
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2662
5 Reallocated_Sector_Ct 0x0033 100 100 011 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0
9 Power_On_Half_Minutes 0x0032 100 100 000 Old_age Always - 3008h+04m
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1446
191 G-Sense_Error_Rate 0x0012 097 097 000 Old_age Always - 38011
194 Temperature_Celsius 0x0022 118 067 000 Old_age Always - 40
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 419586
196 Reallocated_Event_Count 0x0032 099 099 000 Old_age Always - 4
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 051 Old_age Always - 0
201 Soft_Read_Error_Rate 0x0012 100 100 000 Old_age Always - 0
223 Load_Retry_Count 0x0012 100 100 000 Old_age Always - 4
225 Load_Cycle_Count 0x0012 069 069 000 Old_age Always - 315362
255 Unknown_Attribute 0x000a 100 100 051 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 150 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 150 occurred at disk power-on lifetime: 3001 hours (125 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b1 c1 00 00 00 00 a0 00 00:01:06.375 DEVICE CONFIGURATION FREEZE LOCK [OBS-ACS-3]
f5 00 00 00 00 00 a0 00 00:01:06.375 SECURITY FREEZE LOCK
c6 00 10 00 00 00 a0 00 00:01:06.313 SET MULTIPLE MODE
ef 03 45 00 00 00 a0 00 00:01:06.313 SET FEATURES [Set transfer mode]
ef 03 0c 00 00 00 a0 00 00:01:06.313 SET FEATURES [Set transfer mode]
Error 149 occurred at disk power-on lifetime: 3001 hours (125 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 40 ec 06 c1 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b1 c1 40 ec 06 c1 a0 00 00:01:19.000 DEVICE CONFIGURATION FREEZE LOCK [OBS-ACS-3]
70 ff 50 01 00 00 a0 00 00:01:19.000 SEEK [OBS-7]
10 ff 50 12 a0 07 a1 00 00:01:19.000 RECALIBRATE [OBS-4]
91 ff 3f 01 00 00 ae 00 00:01:19.000 INITIALIZE DEVICE PARAMETERS [OBS-6]
00 00 01 01 00 00 a0 00 00:01:19.000 NOP [Abort queued commands]
Error 148 occurred at disk power-on lifetime: 3001 hours (125 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b1 c1 00 00 00 00 a0 00 00:00:38.688 DEVICE CONFIGURATION FREEZE LOCK [OBS-ACS-3]
f5 00 00 00 00 00 a0 00 00:00:38.688 SECURITY FREEZE LOCK
c6 00 10 00 00 00 a0 00 00:00:38.625 SET MULTIPLE MODE
ef 03 45 00 00 00 a0 00 00:00:38.625 SET FEATURES [Set transfer mode]
ef 03 0c 00 00 00 a0 00 00:00:38.625 SET FEATURES [Set transfer mode]
Error 147 occurred at disk power-on lifetime: 2955 hours (123 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 eb b8 b9 e6 Error: UNC at LBA = 0x06b9b8eb = 112834795
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 00 01 eb b8 b9 e6 00 00:36:45.625 READ VERIFY SECTOR(S)
c8 00 01 00 00 00 e0 00 00:36:45.625 READ DMA
Error 146 occurred at disk power-on lifetime: 2955 hours (123 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 ea b8 b9 e6 Error: UNC at LBA = 0x06b9b8ea = 112834794
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 00 01 ea b8 b9 e6 00 00:36:44.188 READ VERIFY SECTOR(S)
c8 00 01 00 00 00 e0 00 00:36:44.188 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
jib@mx1jib:~
$
Exact pour les phrases ; ce que je fais c'est de placer dans le lecteur le DVD-live, d’appuyer sur la touche "end" du clavier, ce Live-DVD se lancera et ensuite "clic" sur "boot hard-disk" ce qui va lancer la dernière installe et la seule, la MX15 ..cyrilus31 wrote:Bon il a passé le test SMART. A priori ce n'est pas la santé de ton DD qui est en cause...
Toujours le même message Hard disk boot sector invalid...... Press 'H' to retry hard disk , any other key for Floppy?
Je vais chercher un peu car là je n'ai pas d'idée. A+
Code: Select all
fsck /dev/sda
C'est exactement ce que je fais depuis pas mal d'années sans arriver a ce point de non-retour... J'ai trouvé un D.D même Go , même marque mais pas même longévité...A ce prix c'est pour pas grand chose...Je tente une autre installe avec le DVD-live de la AntiX 16 dans le même D.D. je verrais ce qu'il se passe...cyrilus31 wrote:A l'installation as-tu personnalisé certains points comme le partitionnement?
Essaie éventuellementet donne-moi le retour stp.Code: Select all
fsck /dev/sda
Après ça s'il n'y a rien de tangible je n'ai pas d'autres idées que de te suggérer de retenter l'installation, tout par défaut (comme utiliser tout le disque) en automatique et tant qu'à faire en MX 16.1 ou antiX 16.2.
A+
Code: Select all
jib@mx1jib:~
$ fsck /dev/sda
fsck from util-linux 2.25.2
e2fsck 1.42.12 (29-Aug-2014)
fsck.ext2: Permission non accordée lors de la tentative d'ouverture de /dev/sda
Vous devez avoir un accès r/w au système de fichiers ou être root
jib@mx1jib:~
$ sudo su
[sudo] password for jib:
root@mx1jib:/home/jib# fsck /dev/sda
fsck from util-linux 2.25.2
e2fsck 1.42.12 (29-Aug-2014)
/dev/sda est en cours d'utilisation.
e2fsck: Ne peut continuer, arrêt immédiat.